При работа линейни задвижващи механизми, има много продуктови спецификации, които потребителите трябва да разберат. Някои примери за задвижващ механизъм specifications that are important may include speed, force, current draw, and dimensions. There is however one element of a linear actuator that can be tricky to gauge, the ниво на шумМного потребители често не знаят със сигурност идеалните нива на шум или ограничения, докато не започнат да работят с линейни задвижващи механизми и не осъзнаят, че нивото на шум може да е твърде високо. Въпреки че е възможно... връщане Ако закупите предишни задвижващи механизми и ги замените с друг модул за по-ниско ниво на шум от линейния задвижващ механизъм, ще е необходимо време и ресурси за връщане на модула и закупуване на нов. В други случаи е възможно да няма модул с достатъчно ниско ниво на шум, който да отговаря на изискванията на определено приложение. За щастие, има начини за преодоляване на шума от използвания задвижващ механизъм. В тази статия ще разгледаме няколко решения за преодоляване на силния механичен шум, генериран от линейните задвижващи механизми.
Работният шум на нашите задвижващи механизми ще бъде посочен на всеки от тях. информационен лист.
Скоростна кутия
Най-често срещаният механичен шум в линейни задвижващи механизми usually comes from the gearbox. The gears can turn incredibly fast depending on the gear ratio the gearbox uses. Since the noise created can be very loud, you can apply grease to the gearbox to reduce this noise. This will also reduce the friction between the gears and therefore reduce the noise. Note that when the actuator is operating in a high-temperature environment, the grease inside the gearbox can melt away, so it is ideal to reapply some gear grease after the units have been operated for a long time in a high-temperature environment.
On the other end of the spectrum, if the actuator is operating continuously in a very cold environment, the grease that acts as a lubricant can become condensed or even frozen. This will cause the unit to generate a lot of noise and may even break down. If that is the case, it is better to replace the grease in the gearbox with new lubricant that has a lower functional temperature.
Последното нещо, за което трябва да внимавате относно шума от скоростната кутия, е видът зъбни колела, които линейният задвижващ механизъм използва. Металните зъбни колела обикновено генерират повече шум, докато полимерните или пластмасовите зъбни колела генерират по-малко шум. Възможно е вътрешните зъбни колела на задвижващия механизъм да се заменят от метални с пластмасови, но този вид процедура трябва да се извършва внимателно. Металните зъбни колела обикновено се използват поради тяхната дълготрайност и здрава структура, като ги заменят с пластмасови зъбни колела, потребителите рискуват да намалят жизнения цикъл на задвижващия механизъм или дори да намалят товароносимостта. Препоръчваме да се консултирате с директния производител. производител на линейни задвижвания before making this decision for any products.
Позиция на монтажа – Намалете площта на повърхността
A lot of the noise from a linear actuator comes from the vibration in the actuator housing. As the electric motor runs, it causes vibration throughout the body of the linear actuator. When that vibration makes physical contact with a hard surface area, it will generate a lot of noise as a result. Therefore, it is a good idea to reduce the surface area that is making physical contact with the linear actuator as this will prevent most of the vibration noise. If that was not possible, users can also consider applying some soft material between the actuator housing and the hard surface area to reduce the linear actuator noise.
Намерете нов задвижващ механизъм
If the above options still don't reduce the noise from your actuator, then it would be time to find a new one. When looking for a replacement actuator to the current one, there are a few points that you should pay attention to. If your old actuator is a ball screw type, you may want to consider looking for an actuator that uses an ACME screw instead. Ball screw generally has great efficiency on power but tends to make a lot more noise when operating. On the other hand, ACME screw type actuators have lower efficiency, but the actuator sound is much quieter when running.
Прочетете нашите блог to learn more about the ACME screw & Ball Screw type actuators. Alternatively, you may also consider finding a new actuator that has a higher load capacity than the old one. When a linear actuator is operating closer to its full load capacity, it tends to generate more noise. We recommend finding an actuator with a higher load rating when possible as it can still drive the application but with lower linear actuator noise. The actuators that have a higher load rating would usually have a slower speed as well so this method of reducing noise is more suitable for applications that can work with slower speeds.
Разгледайте пълната ни гама от задвижващи механизми за да намерим най-доброто решение за вашето приложение!
Заключение
Actuators are great tools for providing linear motion in an application but can sometimes generate too much noise in certain applications while it is running. By using our tip and tricks, you too can overcome the mechanical noise when operating an actuator. For more information on how to overcome linear actuator noise, please feel free to contact us at 1-800-676-6123 by phone or email us at sales@progressiveautomations.comЩастливи сме да ви помогнем с всички ваши въпроси!