Conjunto de colunas de elevação - 880 lbs - Recorrido de 16"

Não podemos garantir que nossos controles remotos funcionarão com sistemas de controle de terceiros. A pinagem das portas pode variar de uma empresa para outra.

Yes, the L shaped standing desk is orientation-friendly and can be installed by your preference. Here is a step-by-step article that explains how this is possible: FLT-05 User Manual

NOTE: The steps below may vary depending on the remote model that you have. The following instructions were made for the standard RT-11 remote. To set the maximum height for your frame, go to the desired height you would like to set and follow the steps below:

1. Press M and see [5 -] indicated on the display
 
2. Press the UP button and notice [5 -] blinks
 
3. Hold the M button until you see [999] on the display
 
4. The maximum height has now been set

To set the minimum height for your frame, go to the desired height you would like to set and follow the steps below:

1. Press M and see [5 -] indicated on the display
 
2. Press the DOWN button and notice [5 -] blinks
 
3. Hold the M button until you see [000] on the display
 
4. The minimum height has now been set

To reset the limits, follow the steps below:

1. Press M and see [5 -] indicated on the display and release
 
2. Hold the M you see [555]
 
3. Limits have been reset

NOTE: The steps below may vary depending on the remote model you have. The following instructions were made for the standard RT-11 remote.

If you have to hold down the remote’s buttons to get to your pre-set height, this means that your control box is in momentary control. To set your remote to non-momentary mode, follow the steps below

1. Make sure that there is nothing underneath your desk, as we have to enter the reset procedure
 
2. Press and hold the DOWN button until the display shows [ASr]
 
3. Once [ASr] is shown, press and hold down [1] and you may see two values:a. 10.1 = Non-momentary Mode b. 10.2 = Momentary Mode
4. Complete the reset procedure by holding the DOWN button until your standing desk slightly lowers and rises.

Our standing desks have 3 settings for collision detection, and this can be set depending on your preference. To proceed, follow the steps below:

1. Make sure that there is nothing underneath your desk as we have to enter the reset procedure
 
2. Press and hold the DOWN button until the display shows [ASr]
3. Once [ASr] is shown, press and hold the UP [ ^ ] button and you may see three values:a. 10.5 = 11 lbsb. 10.6 = 22 lbsc. 10.7 = 33 lbs
4. Complete the reset procedure by holding the DOWN button until your standing desk slightly lowers and rises.

We have some troubleshooting steps for you to take if you see any of the following error codes on the frames with FLTCON series control boxes:

Сheck the error code here.

If the issue you are experiencing persists after following these steps, please feel free to contact our technical product engineers at 1-800-676-6123, or send us an email at sales@progressiveautomations.com.

Depending on your application, there are different specification requirements you should consider when determining the linear actuator you need. These requirements include force, stroke, speed and mounting dimensions. For detailed actuator information, you can refer to either the datasheet or the specification table located on the selected actuator's product page. You can also contact us to speak with one of our expert engineers.

Ciclo de trabalho é a fração do período de operação em que um atuador linear pode permanecer ativo. Você pode calcular o Ciclo de trabalho de um atuador linear usando a seguinte equação: Ciclo de trabalho (%) = (Tempo em que o atuador linear fica ativo) / (Tempo de um período de operação)

Por exemplo: com um Ciclo de trabalho de 25%, um atuador pode operar por 5 minutos continuamente antes de precisar descansar por 15 minutos antes de voltar a operar.

Recorrido é a distância percorrida pela haste de extensão. Para encontrar o comprimento de Recorrido necessário, meça sua aplicação da posição totalmente retraída até a posição totalmente estendida. A diferença será o comprimento de Recorrido necessário.

Sempre recomendamos adquirir um atuador com uma classificação de força maior do que a exigida pela aplicação. Se não tiver certeza dos seus requisitos de força, este artigo pode ajudar a calcular: Como calcular a força para encontrar o atuador linear certo

Sim, isso é possível. No entanto, depende das unidades que você está utilizando. Para sincronizar atuadores, é necessário algum tipo de Feedback, como um potenciômetro ou sensores de efeito Hall. Para mais informações, veja abaixo alguns de nossos conteúdos principais sobre sincronização de atuadores lineares.

Controlando vários atuadores lineares ao mesmo tempo

Como utilizar as caixas de controle FLTCON-2 e FLTCON-4?

A caixa de controle que você escolher deve ser capaz de fornecer tensão e Corrente suficientes para o seu atuador. Se você não tiver certeza das especificações, por favor, entre em contato conosco.

Alternativamente, você também pode encontrar caixas de controle compatíveis na página do produto do atuador linear selecionado.

Backdriving is when an actuator starts sliding down under load, when it is either overloaded or when the actuator has been damaged. Watch the video.

Dynamic load rating is the amount of weight an actuator can pull or push safely when being powered. Static load rating is the amount of weight the actuator can hold or withstand without back driving when it is not being powered. For example, let's just say you have an actuator installed on a window and the static load rating of the actuator is 100lbs, it could experience backdriving when there is a high wind event, which means there will be more pressure exerted on the actuator which would exceed the 100lbs load rating of the actuator.

Lateral loading is when the actuator experiences forces from the lateral plane. Actuators are not meant to handle lateral forces at all so if it experiences any lateral forces, it will likely damage the actuator or bend the rod. So it's advised never to use lateral forces and always make sure the actuator is fully in line or in sync with your application, so it does not take any load other than the axial load. Watch the video.