Při provozu lineární aktuátory, existuje mnoho specifikací produktů, kterým musí uživatelé porozumět. Některé příklady pohon specifications that are important may include speed, force, current draw, and dimensions. There is however one element of a linear actuator that can be tricky to gauge, the hladina hlukuMnoho uživatelů si často není jistých ideálních hladin hluku nebo omezení, dokud si jejich aplikace s lineárními aktuátory neuvědomí, že hladina hluku může být příliš vysoká. I když je možné návrat Pokud chcete vyměnit předchozí pohony za jinou jednotku s nižší hlučností lineárního pohonu, bude vrácení jednotky a zakoupení nové vyžadovat čas a prostředky. V jiných případech se může stát, že neexistuje jednotka s dostatečně nízkou hladinou hluku, která by splňovala požadavky určité aplikace. Naštěstí existují způsoby, jak překonat hluk používaného pohonu. V tomto článku si probereme několik řešení, jak překonat hlasitý mechanický hluk generovaný lineárními pohony.
Provozní hlučnost našich pohonů je uvedena na každém z našich pohonů. datový list.
Převodovka
Nejčastější mechanický hluk v lineární aktuátory usually comes from the gearbox. The gears can turn incredibly fast depending on the gear ratio the gearbox uses. Since the noise created can be very loud, you can apply grease to the gearbox to reduce this noise. This will also reduce the friction between the gears and therefore reduce the noise. Note that when the actuator is operating in a high-temperature environment, the grease inside the gearbox can melt away, so it is ideal to reapply some gear grease after the units have been operated for a long time in a high-temperature environment.
On the other end of the spectrum, if the actuator is operating continuously in a very cold environment, the grease that acts as a lubricant can become condensed or even frozen. This will cause the unit to generate a lot of noise and may even break down. If that is the case, it is better to replace the grease in the gearbox with new lubricant that has a lower functional temperature.
Poslední věc, na kterou si dát pozor ohledně hluku z převodovky, je typ ozubených kol, které lineární aktuátor používá. Kovová ozubená kola obvykle generují více hluku, zatímco polymerová nebo plastová ozubená kola generují méně hluku. Je možné vyměnit vnitřní ozubená kola aktuátoru z kovu za plastová, ale tento postup by musel být proveden opatrně. Kovová ozubená kola se obecně používají kvůli své dlouhé životnosti a pevné konstrukci, jejich nahrazením plastovými ozubenými koly by uživatelé riskovali snížení životnosti aktuátoru nebo dokonce snížení nosnosti. Doporučujeme konzultaci s přímým výrobcem. výrobce lineárních aktuátorů before making this decision for any products.
Montážní poloha – Zmenšete plochu povrchu
A lot of the noise from a linear actuator comes from the vibration in the actuator housing. As the electric motor runs, it causes vibration throughout the body of the linear actuator. When that vibration makes physical contact with a hard surface area, it will generate a lot of noise as a result. Therefore, it is a good idea to reduce the surface area that is making physical contact with the linear actuator as this will prevent most of the vibration noise. If that was not possible, users can also consider applying some soft material between the actuator housing and the hard surface area to reduce the linear actuator noise.
Najít nový aktuátor
If the above options still don't reduce the noise from your actuator, then it would be time to find a new one. When looking for a replacement actuator to the current one, there are a few points that you should pay attention to. If your old actuator is a ball screw type, you may want to consider looking for an actuator that uses an ACME screw instead. Ball screw generally has great efficiency on power but tends to make a lot more noise when operating. On the other hand, ACME screw type actuators have lower efficiency, but the actuator sound is much quieter when running.
Přečtěte si naše blogu to learn more about the ACME screw & Ball Screw type actuators. Alternatively, you may also consider finding a new actuator that has a higher load capacity than the old one. When a linear actuator is operating closer to its full load capacity, it tends to generate more noise. We recommend finding an actuator with a higher load rating when possible as it can still drive the application but with lower linear actuator noise. The actuators that have a higher load rating would usually have a slower speed as well so this method of reducing noise is more suitable for applications that can work with slower speeds.
Prohlédněte si naši kompletní řadu pohonů najít nejlepší řešení pro vaši aplikaci!
Závěr
Actuators are great tools for providing linear motion in an application but can sometimes generate too much noise in certain applications while it is running. By using our tip and tricks, you too can overcome the mechanical noise when operating an actuator. For more information on how to overcome linear actuator noise, please feel free to contact us at 1-800-676-6123 by phone or email us at sales@progressiveautomations.comRádi vám pomůžeme s jakýmikoli dotazy!