Ved drift lineære aktuatorer, finnes det mange produktspesifikasjoner som brukerne må forstå. Noen eksempler på aktuator specifications that are important may include speed, force, current draw, and dimensions. There is however one element of a linear actuator that can be tricky to gauge, the støynivåMange brukere vet ofte ikke sikkert hva som er det ideelle støynivået eller restriksjonene før de kjører applikasjonen med lineære aktuatorer, og innser at støynivået kan være for høyt. Selv om det er mulig å retur tidligere aktuatorer og erstatte den med en annen enhet for å få en lineær aktuator med lavere støynivå, vil det kreve tid og ressurser å sende enheten tilbake og kjøpe en ny. I andre tilfeller kan det også være mulig at det ikke finnes en enhet med et lavt nok støynivå til å dekke kravene til et bestemt bruksområde. Heldigvis finnes det måter å overvinne støyen fra aktuatoren som ble brukt. I denne artikkelen vil vi gå gjennom flere løsninger for å overvinne den høye mekaniske støyen som genereres fra lineære aktuatorer.
Driftsstøyen fra aktuatorene våre vil være oppført på hver av aktuatorene våre. datablad.
Girkasse
Den vanligste mekaniske støyen i lineære aktuatorer usually comes from the gearbox. The gears can turn incredibly fast depending on the gear ratio the gearbox uses. Since the noise created can be very loud, you can apply grease to the gearbox to reduce this noise. This will also reduce the friction between the gears and therefore reduce the noise. Note that when the actuator is operating in a high-temperature environment, the grease inside the gearbox can melt away, so it is ideal to reapply some gear grease after the units have been operated for a long time in a high-temperature environment.
On the other end of the spectrum, if the actuator is operating continuously in a very cold environment, the grease that acts as a lubricant can become condensed or even frozen. This will cause the unit to generate a lot of noise and may even break down. If that is the case, it is better to replace the grease in the gearbox with new lubricant that has a lower functional temperature.
Det siste du bør se etter når det gjelder støy fra girkassen, er typen gir den lineære aktuatoren bruker. Metallgir genererer vanligvis mer støy, mens polymer- eller plastgir genererer mindre støy i sammenligning. Det er mulig å erstatte de interne girene i en aktuator fra metall til plast, men denne typen prosedyre må gjøres forsiktig. Metallgir brukes vanligvis på grunn av sin lange levetid og sterke struktur. Ved å erstatte dem med plastgir risikerer brukerne å redusere aktuatorens levetid eller til og med redusere lastekapasiteten. Vi anbefaler å konsultere med den direkte produsent av lineære aktuatorer before making this decision for any products.
Monteringsposisjon – Reduser overflatearealet
A lot of the noise from a linear actuator comes from the vibration in the actuator housing. As the electric motor runs, it causes vibration throughout the body of the linear actuator. When that vibration makes physical contact with a hard surface area, it will generate a lot of noise as a result. Therefore, it is a good idea to reduce the surface area that is making physical contact with the linear actuator as this will prevent most of the vibration noise. If that was not possible, users can also consider applying some soft material between the actuator housing and the hard surface area to reduce the linear actuator noise.
Finn en ny aktuator
If the above options still don't reduce the noise from your actuator, then it would be time to find a new one. When looking for a replacement actuator to the current one, there are a few points that you should pay attention to. If your old actuator is a ball screw type, you may want to consider looking for an actuator that uses an ACME screw instead. Ball screw generally has great efficiency on power but tends to make a lot more noise when operating. On the other hand, ACME screw type actuators have lower efficiency, but the actuator sound is much quieter when running.
Les vår blogg to learn more about the ACME screw & Ball Screw type actuators. Alternatively, you may also consider finding a new actuator that has a higher load capacity than the old one. When a linear actuator is operating closer to its full load capacity, it tends to generate more noise. We recommend finding an actuator with a higher load rating when possible as it can still drive the application but with lower linear actuator noise. The actuators that have a higher load rating would usually have a slower speed as well so this method of reducing noise is more suitable for applications that can work with slower speeds.
Se hele vårt utvalg av aktuatorer for å finne den beste løsningen for din applikasjon!
Konklusjon
Actuators are great tools for providing linear motion in an application but can sometimes generate too much noise in certain applications while it is running. By using our tip and tricks, you too can overcome the mechanical noise when operating an actuator. For more information on how to overcome linear actuator noise, please feel free to contact us at 1-800-676-6123 by phone or email us at sales@progressiveautomations.comVi hjelper deg gjerne med eventuelle spørsmål du måtte ha!