Bu örnek kod, doğrusal bir aktüatörün akımını izlemek için MegaMoto Plus ve Arduino Uno kullanmaktadır; ancak benzer ürünler de alternatif olarak kullanılabilir.

/* Code to monitor the current amp draw of the actuator, and to cut power if it rises above a certain amount. Written by Progressive Automations August 19th, 2015 Hardware: - RobotPower MegaMoto control boards - Arduino Uno - 2 pushbuttons */ const int EnablePin = 8;
const int PWMPinA = 11;
const int PWMPinB = 3; // pins for Megamoto const int buttonLeft = 4;
const int buttonRight = 5;//buttons to move the motor const int CPin1 = A5; // motor feedback int leftlatch = LOW;
int rightlatch = LOW;//motor latches (used for code logic) int hitLimits = 0;//start at 0
int hitLimitsmax = 10;//values to know if travel limits were reached long lastfeedbacktime = 0; // must be long, else it overflows
int firstfeedbacktimedelay = 750; //first delay to ignore current spike
int feedbacktimedelay = 50; //delay between feedback cycles, how often you want the motor to be checked
long currentTimefeedback = 0; // must be long, else it overflows int debounceTime = 300; //amount to debounce buttons, lower values makes the buttons more sensitive
long lastButtonpress = 0; // timer for debouncing
long currentTimedebounce = 0; int CRaw = 0; // input value for current readings
int maxAmps = 0; // trip limit bool dontExtend = false;
bool firstRun = true;
bool fullyRetracted = false;//program logic void setup()
{ Serial.begin(9600); pinMode(EnablePin, OUTPUT); pinMode(PWMPinA, OUTPUT); pinMode(PWMPinB, OUTPUT);//Set motor outputs pinMode(buttonLeft, INPUT); pinMode(buttonRight, INPUT);//buttons digitalWrite(buttonLeft, HIGH); digitalWrite(buttonRight, HIGH);//enable internal pullups pinMode(CPin1, INPUT);//set feedback input currentTimedebounce = millis(); currentTimefeedback = 0;//Set initial times maxAmps = 15;// SET MAX CURRENT HERE }//end setup void loop()
{ latchButtons();//check buttons, see if we need to move moveMotor();//check latches, move motor in or out }//end main loop void latchButtons()
{ if (digitalRead(buttonLeft)==LOW)//left is forwards { currentTimedebounce = millis() - lastButtonpress;// check time since last press if (currentTimedebounce> debounceTime && dontExtend == false)//once you've tripped dontExtend, ignore all forwards presses { leftlatch = !leftlatch;// if motor is moving, stop, if stopped, start moving firstRun = true;// set firstRun flag to ignore current spike fullyRetracted = false; // once you move forwards, you are not fully retracted lastButtonpress = millis();//store time of last button press return; }//end if }//end btnLEFT if (digitalRead(buttonRight)==LOW)//right is backwards { currentTimedebounce = millis() - lastButtonpress;// check time since last press if (currentTimedebounce> debounceTime) { rightlatch = !rightlatch;// if motor is moving, stop, if stopped, start moving firstRun = true;// set firstRun flag to ignore current spike lastButtonpress = millis();//store time of last button press return; }//end if }//end btnRIGHT
}//end latchButtons void moveMotor()
{ if (leftlatch == HIGH) motorForward(255); //speed = 0-255 if (leftlatch == LOW) motorStop(); if (rightlatch == HIGH) motorBack(255); //speed = 0-255 if (rightlatch == LOW) motorStop(); }//end moveMotor void motorForward(int speeed)
{ while (dontExtend == false && leftlatch == HIGH) { digitalWrite(EnablePin, HIGH); analogWrite(PWMPinA, speeed); analogWrite(PWMPinB, 0);//move motor if (firstRun == true) delay(firstfeedbacktimedelay); // bigger delay to ignore current spike else delay(feedbacktimedelay); //small delay to get to speed getFeedback(); firstRun = false; latchButtons();//check buttons again }//end while }//end motorForward void motorBack (int speeed)
{ while (rightlatch == HIGH) { digitalWrite(EnablePin, HIGH); analogWrite(PWMPinA, 0); analogWrite(PWMPinB, speeed);//move motor if (firstRun == true) delay(firstfeedbacktimedelay);// bigger delay to ignore current spike else delay(feedbacktimedelay); //small delay to get to speed getFeedback(); firstRun = false; latchButtons();//check buttons again }//end while dontExtend = false;//allow motor to extend again, after it has been retracted }//end motorBack void motorStop()
{ analogWrite(PWMPinA, 0); analogWrite(PWMPinB, 0); digitalWrite(EnablePin, LOW); firstRun = true;//once the motor has stopped, reenable firstRun to account for startup current spikes }//end stopMotor void getFeedback()
{ CRaw = analogRead(CPin1); // Read current if (CRaw == 0 && hitLimits < hitLimitsmax) hitLimits = hitLimits + 1; else hitLimits = 0; // check to see if the motor is at the limits and the current has stopped if (hitLimits == hitLimitsmax && rightlatch == HIGH) { rightlatch = LOW; // stop motor fullyRetracted = true; }//end if else if (hitLimits == hitLimitsmax && leftlatch == HIGH) { leftlatch = LOW;//stop motor hitLimits = 0; }//end if if (CRaw> maxAmps) { dontExtend = true; leftlatch = LOW; //stop if feedback is over maximum }//end if lastfeedbacktime = millis();//store previous time for receiving feedback
}//end getFeedback

Bu örnek kod, Arduino Uno kullanarak 4 adede kadar doğrusal aktüatörümüzü nasıl kontrol edeceğinizi göstermektedir. LC-82 MultiMoto Arduino ShieldAncak, benzer ürünler ikame olarak kullanılabilir. Bu kod yalnızca MultiMoto'nun her kanalındaki mevcut sınırlamalar dahilindeki aktüatör modelleriyle (örneğin PA-14 ve PA-14P) kullanım için tasarlanmıştır.

/* Robot Power MultiMoto sürücüsünü kullanarak 4 adede kadar aktüatörü kontrol etmek için örnek kod. Donanım: - Robot Power MultiMoto - Arduino Uno Bağlantı: - Aktüatörleri MultiMoto kartındaki M1, M2, M3, M4 bağlantılarına bağlayın. - Negatif (siyah) ucu sağ bağlantıya, pozitif (kırmızı) ucu sol bağlantıya bağlayın. - BAT terminallerine 12 voltluk bir güç kaynağı (yüksüz durumda motor başına minimum 1A, tam yüklü durumda motor başına 8A) bağlayın. Pozitif ve negatif uçların doğru yerlere yerleştirildiğinden emin olun. Kod, Robot Power tarafından sağlanan örnek koddan Progressive Automations tarafından değiştirilmiştir.  http://www.robotpower.com/downloads/ Robot Power MultiMoto v1.0 demo This software is released into the Public Domain
*/ // include the SPI library: #include 
// L9958 slave select pins for SPI
#define SS_M4 14
#define SS_M3 13
#define SS_M2 12
#define SS_M1 11
// L9958 DIRection pins
#define DIR_M1 2
#define DIR_M2 3
#define DIR_M3 4
#define DIR_M4 7
// L9958 PWM pins
#define PWM_M1 9
#define PWM_M2 10 // Timer1
#define PWM_M3 5
#define PWM_M4 6 // Timer0 // L9958 Enable for all 4 motors
#define ENABLE_MOTORS 8 int pwm1, pwm2, pwm3, pwm4;
boolean dir1, dir2, dir3, dir4; void setup() { unsigned int configWord; // put your setup code here, to run once: pinMode(SS_M1, OUTPUT); digitalWrite(SS_M1, LOW); // HIGH = not selected pinMode(SS_M2, OUTPUT); digitalWrite(SS_M2, LOW); pinMode(SS_M3, OUTPUT); digitalWrite(SS_M3, LOW); pinMode(SS_M4, OUTPUT); digitalWrite(SS_M4, LOW); // L9958 DIRection pins pinMode(DIR_M1, OUTPUT); pinMode(DIR_M2, OUTPUT); pinMode(DIR_M3, OUTPUT); pinMode(DIR_M4, OUTPUT); // L9958 PWM pins pinMode(PWM_M1, OUTPUT); digitalWrite(PWM_M1, LOW); pinMode(PWM_M2, OUTPUT); digitalWrite(PWM_M2, LOW); // Timer1 pinMode(PWM_M3, OUTPUT); digitalWrite(PWM_M3, LOW); pinMode(PWM_M4, OUTPUT); digitalWrite(PWM_M4, LOW); // Timer0 // L9958 Enable for all 4 motors pinMode(ENABLE_MOTORS, OUTPUT); digitalWrite(ENABLE_MOTORS, HIGH); // HIGH = disabled / /******* Set up L9958 chips ********* ' L9958 Config Register ' Bit '0 - RES '1 - DR - reset '2 - CL_1 - curr limit '3 - CL_2 - curr_limit '4 - RES '5 - RES '6 - RES '7 - RES '8 - VSR - voltage slew rate (1 enables slew limit, 0 disables) '9 - ISR - current slew rate (1 enables slew limit, 0 disables) '10 - ISR_DIS - current slew disable '11 - OL_ON - open load enable '12 - RES '13 - RES '14 - 0 - always zero '15 - 0 - always zero */ // set to max current limit and disable ISR slew limiting configWord = 0b0000010000001100; SPI.begin(); SPI.setBitOrder(LSBFIRST); SPI.setDataMode(SPI_MODE1); // clock pol = low, phase = high // Motor 1 digitalWrite(SS_M1, LOW); SPI.transfer(lowByte(configWord)); SPI.transfer(highByte(configWord)); digitalWrite(SS_M1, HIGH); // Motor 2 digitalWrite(SS_M2, LOW); SPI.transfer(lowByte(configWord)); SPI.transfer(highByte(configWord)); digitalWrite(SS_M2, HIGH); // Motor 3 digitalWrite(SS_M3, LOW); SPI.transfer(lowByte(configWord)); SPI.transfer(highByte(configWord)); digitalWrite(SS_M3, HIGH); // Motor 4 digitalWrite(SS_M4, LOW); SPI.transfer(lowByte(configWord)); SPI.transfer(highByte(configWord)); digitalWrite(SS_M4, HIGH); //Set initial actuator settings to pull at 0 speed for safety dir1 = 0; dir2 = 0; dir3 = 0; dir4 = 0; // Set direction pwm1 = 0; pwm2 = 0; pwm3 = 0; pwm4 = 0; // Set speed (0-255) digitalWrite(ENABLE_MOTORS, LOW);// LOW = enabled
} // End setup void loop() { dir1 = 1; pwm1 = 255; //set direction and speed digitalWrite(DIR_M1, dir1); analogWrite(PWM_M1, pwm1); // write to pins dir2 = 0; pwm2 = 128; digitalWrite(DIR_M2, dir2); analogWrite(PWM_M2, pwm2); dir3 = 1; pwm3 = 255; digitalWrite(DIR_M3, dir3); analogWrite(PWM_M3, pwm3); dir4 = 0; pwm4 = 128; digitalWrite(DIR_M4, dir4); analogWrite(PWM_M4, pwm4); delay(5000); // wait once all four motors are set dir1 = 0; pwm1 = 128; digitalWrite(DIR_M1, dir1); analogWrite(PWM_M1, pwm1); dir2 = 1; pwm2 = 255; digitalWrite(DIR_M2, dir2); analogWrite(PWM_M2, pwm2); dir3 = 0; pwm3 = 128; digitalWrite(DIR_M3, dir3); analogWrite(PWM_M3, pwm3); dir4 = 1; pwm4 = 255; digitalWrite(DIR_M4, dir4); analogWrite(PWM_M4, pwm4); delay(5000); }//end void loop

This example code is for combining the Wasp single-channel speed controller with the Arduino Uno to control the motion of a linear actuatorAncak, benzer ürünler ikame olarak kullanılabilir.

/*Sample code for the Robot Power Wasp. This ESC is controlled using RC signals, with pulses ranging from 1000 - 2000 microseconds. The main loop of this program holds the actuator still for 1 second, extends for 2 seconds, stops for 1 second, retracts for 2 seconds, and repeats. Modified by Progressive Automations, using the original example code "Sweep" from the Arduino example libraries. Hardware: - 1 Wasp Controller - Arduino Uno Wiring: Control side: - Connect the red/black to +5v and GND - Connect the yellow wire to your signal pin on the Arduino (in this example, pin 9) Power Side: - Connect the +/- of the motors power supply to the +/- connections on the Wasp - Connect the +/- of the actuator to the remaining two connections This example code is in the public domain.
*/ #include  Servo myservo; // Bir servoyu kontrol etmek için servo nesnesi oluşturun // Çoğu kartta on iki servo nesnesi oluşturulabilir int pos = 0; // Servo pozisyonunu saklamak için değişken void setup() { myservo.attach(9); // 9 numaralı pindeki servoyu servo nesnesine bağlar } void loop() { myservo.writeMicroseconds(1500); // Durdurma sinyali delay(1000); // 1 saniye myservo.writeMicroseconds(2000); // Tam hız ileri sinyali delay(2000); // 2 saniye myservo.writeMicroseconds(1500); // Durdurma sinyali delay(1000); // 1 saniye myservo.writeMicroseconds(1000); // Tam hız geri sinyali delay(2000); // 2 saniye }

Bu örnek kod, bizim yöntemimizi kullanmaktadır. röleler Arduino Uno ile doğrusal aktüatörü kontrol etmek mümkün, ancak benzer ürünler de ikame olarak kullanılabilir. Detaylı bilgi için yazımızı okuyabilirsiniz. blog yazısı Daha fazla ayrıntı için.

const int forwards = 7;
const int backwards = 6;//assign relay INx pin to arduino pin void setup() { pinMode(forwards, OUTPUT);//set relay as an output
pinMode(backwards, OUTPUT);//set relay as an output } void loop() { digitalWrite(forwards, LOW); digitalWrite(backwards, HIGH);//Activate the relay one direction, they must be different to move the motor delay(2000); // wait 2 seconds digitalWrite(forwards, HIGH); digitalWrite(backwards, HIGH);//Deactivate both relays to brake the motor delay(2000);// wait 2 seconds digitalWrite(forwards, HIGH); digitalWrite(backwards, LOW);//Activate the relay the other direction, they must be different to move the motor delay(2000);// wait 2 seconds digitalWrite(forwards, HIGH); digitalWrite(backwards, HIGH);//Deactivate both relays to brake the motor delay(2000);// wait 2 seconds }

Bu örnek kod bizimkini kullanıyor. LC-80Arduino Uno, herhangi bir doğrusal aktüatör ve bir güç kaynağı; ancak benzer ürünler ikame olarak kullanılabilir. Kod ve işlevi hakkında daha fazla detayı web sitemizde bulabilirsiniz. blog yazısı.

//Use the jumpers on the board to select which pins will be used
int EnablePin1 = 13;
int PWMPinA1 = 11;
int PWMPinB1 = 3; int extendtime = 10 * 1000; // 10 seconds, times 1000 to convert to milliseconds
int retracttime = 10 * 1000; // 10 seconds, times 1000 to convert to milliseconds
int timetorun = 300 * 1000; // 300 seconds, times 1000 to convert to milliseconds int duty;
int elapsedTime;
boolean keepMoving; void setup() { Serial.begin(9600); pinMode(EnablePin1, OUTPUT);//Enable the board pinMode(PWMPinA1, OUTPUT); pinMode(PWMPinB1, OUTPUT);//Set motor outputs elapsedTime = 0; // Set time to 0 keepMoving = true; //The system will move }//end setup
void loop() { if (keepMoving) { digitalWrite(EnablePin1, HIGH); // enable the motor pushActuator(); delay(extendtime); stopActuator(); delay(10);//small delay before retracting pullActuator(); delay(retracttime); stopActuator(); elapsedTime = millis();//how long has it been? if (elapsedTime> timetorun) {//if it's been 300 seconds, stop Serial.print("Elapsed time is over max run time. Max run time: "); Serial.println(timetorun); keepMoving = false; } }//end if
}//end main loop void stopActuator() { analogWrite(PWMPinA1, 0); analogWrite(PWMPinB1, 0); // speed 0-255
} void pushActuator() { analogWrite(PWMPinA1, 255); analogWrite(PWMPinB1, 0); // speed 0-255
} void pullActuator() { analogWrite(PWMPinA1, 0); analogWrite(PWMPinB1, 255);//speed 0-255
}

Bu program, doğrusal bir aktüatörün hareket mesafesini sürekli olarak uzatmak ve kısaltmak için kullanılabilir.

SETUP LOOP CODE
void setup() { Serial.begin(9600); // initialize serial communication at 9600 bits per second pinMode(out_lim, INPUT_PULLUP); // configures pin 45 as input pin pinMode(in_lim, INPUT_PULLUP); // configures pin 53 as input pin pinMode(run_f, OUTPUT); // configures pin 25 as output pin pinMode(run_r, OUTPUT); // configures pin 30 as output pin retract(); // retracts the stroke on startup delay(500);
}
void extend() // this function enables the motor to run
{ digitalWrite(run_f, LOW); digitalWrite(run_r, HIGH);
} void retract() // this function reverses the direction of motor
{ digitalWrite(run_f, LOW); digitalWrite(run_r, LOW); } void run_stop() // this function disables the motor
{ digitalWrite(run_f, HIGH); digitalWrite(run_r, HIGH);
}
void loop() { int out_lim_state = digitalRead(out_lim); // reads the limit switches and saves its value int in_lim_state = digitalRead(in_lim); Serial.print("outer limit switch value "), Serial.println(out_lim_state); // 0 -> limit switch is pressed Serial.print("inner limit switch value "), Serial.println(in_lim_state); // 1 -> limit switch is not pressed if (out_lim_state == 0 && in_lim_state == 1) // if outer limit switch is pressed and inner is not (extended all the way) { retract(); // retract the stroke } else if (out_lim_state == 1 && in_lim_state == 0) // if inner limit switch is pressed and outer is not (reracted all the way) { extend(); // extend the stroke } else // otherwise do nothing { }
delay(5); // delay in between reads for stability
}